Australian Capital Territory Consolidated Regulations Australian Capital Territory Consolidated Regulations(see s 2)
Note 1 The Legislation Act contains definitions and other provisions relevant to this regulation.
Note 2 For example, the Legislation Act, dict, pt 1, defines the following terms:
• document
• person.
Note 3 Terms used in this regulation have the same meaning that they have in the Scaffolding and Lifts Act 1912 (see Legislation Act, s 148). For example, the following terms are defined in the Scaffolding and Lifts Act 1912, dict:
• crane
• dogger
• gear
• inspector
• lift
• plant.
"analogous" means radically analogous in relation to prime characteristics.
"approved" means approved in writing by the chief inspector.
"axial stress" means one produced by a force or load acting parallel to and concentrically with the longitudinal neutral axis of the member concerned, and is the initial stress so produced, before any redistribution that may accompany resultant elastic deformation of the member.
"bearing pressure", in relation to a pin or shaft in a plain bearing, means bearing pressure calculated as for a plane rectangular area of length equal to the length of the bearing, and of width equal to the diameter of the bearing.
"birdcage scaffolding"—see section 85.
"cantilever scaffolding"—see section 85.
"conveyor", for part 4 (Lifts)—see section 16.
"dead loads" means all loads of which the principal effects remain constant during operation or manipulation of the crane, lift, hoist, scaffolding, plant or gear concerned.
"designed" means effectively and correctly designed for its purpose in complete accordance with this regulation or, if provision is not included in this regulation, effectively and correctly designed for its purpose in an approved way.
"drawings" means permanent, fully detailed and fully dimensioned and annotated engineering drawings, clear, distinct, and to a commonly used scale, which are sufficiently complete for engineering workshop use to enable faithful manufacture of all items depicted.
"dynamically irreversible" means incapable of being set or kept in motion by energy applied at or to the power output member or part of any mechanism, linkage or device.
"dynamically reversible" means capable of being set or kept in motion by energy applied at or to the power output member or part of any mechanism, linkage or device.
"explosive-powered tool", for part 9A (Explosive-powered tools—safety measures)—see section 118A.
"fixed end" means for purposes of stress determination, a fixed end or fixed connection so designed that it effectively maintains and preserves the tangent to the elastic curve of the end of the member concerned in its original direction and position, irrespective of applied loading.
"forged steel" means hot forged from steel conforming to Australian Standard Specification No E17—(1944 T.) General Locomotive Forgings of K quality, and Australian Standard Specification No B63—1938 Carbon Steel Forgings (Primarily for Cranes and Hoists).
"free end" means for purposes of stress determination, a free end not specifically secured in a way that will effectively prevent its translation.
"heavy duty scaffolding"—see section 85.
"high tensile structural steel" means steel conforming to British Standard Specification No 548—1934, High Tensile Structural Steel for Bridges etc and General Building Construction, or British Standard Specification No 968—1941, High Tensile (Fusion Welding Quality) Steel for Bridges, etc, and General Building Construction promulgated by Standards Australia.
"hinged end" means for purposes of stress determination, a hinged end or hinged connection not specifically and effectively designed to transmit major restraining or other moments.
"in commission" means in commission but not necessarily active.
"independent pole scaffolding"—see section 85.
"light duty scaffolding"—see section 85.
"light swinging stage"—see section 85.
"limiting" means—
(a) a maximum such that if it were increased; or
(b) a minimum such that if it were decreased;
the increase or decrease would occasion contravention of the Act or this regulation, or in any way prejudice the safe working of the crane, lift, hoist, scaffolding or plant concerned.
"live loads" means all loads of which the principal effects vary during operation or manipulation of the crane, lift, hoist, scaffolding, plant or gear concerned, and include the working load and all loads due to inertia, momentum, braking and wind.
"mild steel" means—
(a) except in relation to bolts or rivets—mild steel conforming to Australian Standard Specification No A.1—1940 Rolled Steel Sections for Structural Purposes; and
(b) in relation to bolts or rivets—a mild steel approved by the chief inspector as being suitable for its purpose.
"projectile", for part 9A (Explosive-powered tools—safety measures)—see section 118A.
"qualified operator", for part 9A (Explosive-powered tools—safety measures)—see section 118A.
"roller" means a wheel or cylinder that is either without an axle, or in which an axle or equivalent device is employed principally for purposes of alignment and location as distinct from the transmission of loads or forces.
"run"—see section 85.
S.A.A. Wiring Rules means Australian Standard Rules for the electrical equipment of buildings, structures and premises, published by the Standards Australia, known as the S.A.A. Wiring Rules. (First issued June, 1931, revised December, 1934, revised January, 1940. Reprinted including corrigenda of February, 1940, February, 1943, and March, 1944. Amendment 3, 1945. All redated 1945. Amendment 4, January, 1946, redated 1946.).
"safety gear", for part 4 (Lifts)—see section 16.
"safe working load" (or working load) means the greatest burden that may be imposed without contravening any provision of this regulation in or on the lifting or lowering instrument with which any crane, lift or hoist is provided for lifting or lowering, or on any platform of any scaffold, but does not include wind loads or any increase consequential to section 125 or the weight of the lifting hook, yoke, kibble, box, cage, vessel or other medium by which the load is raised or lowered, or the weight of the platform or framework of any scaffold.
"second-hand" means evidencing previous usage that might reasonably be expected or anticipated to have resulted in wear or abrasion, distortion, fatigue, misalignment, cold working, strain hardening, overheating, corrosion, or other damage or deterioration, affecting the item concerned in whole or in part, and, in relation to any material, second-hand means not plainly self evidently new.
"section" means actual section before any deformation that may follow or accompany application of stress and, unless otherwise stated, all sections must lie in planes normal to the longitudinal axes of the members concerned.
"service lift", for part 4 (Lifts)—see section 16.
"single pole scaffolding"—see section 85.
"static counterbalance weights" includes all counterbalance weights that do not move relatively to the crane, hoist, lift, scaffolding, plant or gear concerned or to its supporting structure.
"strength" means computed strength except in relation to the strengths of materials or ropes, and unless the chief inspector specifically approves otherwise.
"stress" means stress measured in tons per square inch, after including all increases prescribed by this regulation.
"suspended scaffolding"—see section 85.
"toe board"—see section 85.
"tool", for part 9A (Explosive-powered tools—safety measures)—see section 118A.
"transverse stress" means the longitudinal tensile or compressive fibre stress resulting at the skin of a member from forces that cause flexure, but not include the axial stress.
"under power" means energised by any agency other than manual or gravitational.
"use", an explosive-powered tool, for part 9A (Explosive-powered tools—safety measures)—see section 118A (3).
"work", for part 9A (Explosive-powered tools—safety measures)—see section 118A.
"working load"—see safe working load.
Amending and modifying laws are annotated in the legislation history and the amendment history. Current modifications are not included in the republished law but are set out in the endnotes.
Not all editorial amendments made under the Legislation Act 2001, part 11.3 are annotated in the amendment history. Full details of any amendments can be obtained from the Parliamentary Counsel's Office.
Uncommenced amending laws and expiries are listed in the legislation history and the amendment history. These details are underlined. Uncommenced provisions and amendments are not included in the republished law but are set out in the last endnote.
If all the provisions of the law have been renumbered, a table of renumbered provisions gives details of previous and current numbering.
The endnotes also include a table of earlier republications.
|
am = amended |
ord = ordinance |
|
amdt = amendment |
orig = original |
|
ch = chapter |
par = paragraph/subparagraph |
|
def = definition |
pres = present |
|
dict = dictionary |
prev = previous |
|
disallowed = disallowed by the Legislative |
(prev...) = previously |
|
Assembly |
pt = part |
|
div = division |
r = rule/subrule |
|
exp = expires/expired |
renum = renumbered |
|
Gaz = gazette |
reloc = relocated |
|
hdg = heading |
R[X] = Republication No |
|
IA = Interpretation Act 1967 |
RI = reissue |
|
ins = inserted/added |
s = section/subsection |
|
LA = Legislation Act 2001 |
sch = schedule |
|
LR = legislation register |
sdiv = subdivision |
|
sub = substituted |
|
|
mod = modified/modification |
SL = Subordinate Law |
|
o = order |
underlining = whole or part not commenced |
|
om = omitted/repealed |
or to be expired |
This regulation was originally a NSW regulation—the Regulations made under the Scaffolding and Lifts Act 1912 (NSW).
The Scaffolding and Lifts Act 1912 (NSW) and this regulation were applied, in a modified form, as ACT laws by the Scaffolding and Lifts Act 1957 (now repealed).
This regulation was renamed by the Scaffolding and Lifts Regulations Amendment SL 1999 No 19 and later under the Legislation Act 2001.
Under the Interpretation Act 1967 (repealed), s 65 all former NSW Acts in force in the ACT immediately before 10 November 1999 (including the Scaffolding and Lifts Act 1912) became, for all purposes, laws made by the ACT Legislative Assembly.
Under the Scaffolding and Lifts Act 1912, s 28 (now expired) the Scaffolding and Lifts Regulation 1950 became, on 29 March 2001, for all purposes, a regulation made under that Act. This completed the process of making the regulation fully into an ACT law.
Before 11 May 1989, regulations commenced on their notification day unless otherwise stated (see Interpretation Act 1967 s 50).
Before 11 May 1989, ordinances commenced on their notification day unless otherwise stated (see Seat of Government (Administration) Act 1910 (Cwlth), s 12).
NSW legislation
Scaffolding and Lifts Regulation 1950
notified 25 May 1950 (NSW Gaz 1950 No 86)
commenced 1 June 1950 (s 1 (1))
as amended by
Amendments of regulations made under the Scaffolding and Lifts Act 1912
notified 1 September 1950 (NSW Gaz 1950 No 141)
commenced 1 September 1950
Amendments of regulations made under the Scaffolding and Lifts Act 1912
notified 3 November 1950 (NSW Gaz 1950 No 168)
commenced 3 November 1950
Amendments of regulations made under the Scaffolding and Lifts Act 1912
notified 6 March 1953 (NSW Gaz 1953 No 44)
commenced 6 March 1953
Amendments of regulations made under the Scaffolding and Lifts Act 1912
notified 3 December 1954 (NSW Gaz 1954 No 197)
commenced 3 December 1954
Amendments of regulations made under the Scaffolding and Lifts Act 1912
notified 5 August 1955 (NSW Gaz 1955 No 76)
commenced 5 August 1955
Amendments of regulations made under the Scaffolding and Lifts Act 1912
notified 9 March 1956 (NSW Gaz 1956 No 24)
commenced 9 March 1956
Amendments of regulations made under the Scaffolding and Lifts Act 1912
notified 22 June 1956 (NSW Gaz 1956 No 69)
commenced 22 June 1956
Amendments of regulations made under the Scaffolding and Lifts Act 1912
notified 19 October 1956 (NSW Gaz 1956 No 113)
commenced 19 October 1956
Amendments of regulations made under the Scaffolding and Lifts Act 1912
notified 1 March 1957 (NSW Gaz 1957 No 29)
commenced 1 March 1957
Commonwealth legislation
Scaffolding and Lifts Act 1957 No 8 sch pt 2 (as am by ord 1968 No 5; ord 1974 No 26; ord 1976 No 7; ord 1977 No 28; ord 1981 No 15; ord 1982 No 15; ord 1982 No 68; ord 1983 No 34)
notified 19 September 1957 (Cwlth Gaz 1957 No 51)
commenced 19 September 1957
Scaffolding and Lifts Ordinance 1968 No 5
notified 21 March 1968 (Cwlth Gaz 1968 No 26)
commenced 21 March 1968
Note This ordinance only amends the Scaffolding and Lifts Act 1957 No 8.
Scaffolding and Lifts Ordinance 1974 No 26
notified 30 July 1974 (Cwlth Gaz 1974 No 62)
commenced 30 July 1974
Note This ordinance only amends the Scaffolding and Lifts Act 1957 No 8.
Scaffolding and Lifts Ordinance 1976 No 7
notified 24 February 1976 (Cwlth Gaz 1976 No S38)
commenced 24 February 1976
Note This ordinance only amends the Scaffolding and Lifts Act 1957 No 8.
Scaffolding and Lifts (Amendment) Ordinance 1977 No 28
notified 1 July 1977 (Cwlth Gaz 1977 No S124)
commenced 1 July 1977
Note This ordinance only amends the Scaffolding and Lifts Act 1957 No 8.
Scaffolding and Lifts (Amendment) Ordinance 1981 No 15
notified 30 June 1981 (Cwlth Gaz 1981 No S128)
commenced 30 June 1981
Note This ordinance only amends the Scaffolding and Lifts Act 1957 No 8.
Scaffolding and Lifts (Amendment) Ordinance 1982 No 15
notified 7 May 1982 (Cwlth Gaz 1982 No S93)
commenced 7 May 1982
Note This ordinance only amends the Scaffolding and Lifts Act 1957 No 8.
Scaffolding and Lifts (Amendment) Ordinance (No 2) 1982 No 68
notified 18 August 1982 (Cwlth Gaz 1982 No S174)
commenced 18 August 1982
Note This ordinance only amends the Scaffolding and Lifts Act 1957 No 8.
Scaffolding and Lifts (Amendment) Ordinance 1983 No 34
notified 29 September 1983 (Cwlth Gaz 1983 No S226)
commenced 1 October 1983 (s 2)
Note This ordinance only amends the Scaffolding and Lifts Act 1957 No 8.
Regulations under the Scaffolding and Lifts Act 1912 (NSW) in their application to the Territory (Amendment) SL 1986 No 9
notified 31 July 1986 (Cwlth Gaz 1986 No S375)
commenced 31 July 1986
Self-Government (Consequential Amendments) Ordinance 1989 No 38 sch 2
notified 10 May 1989 (Cwlth Gaz 1989 No S160)
s 1, s 2 commenced 10 May 1989 (s 2 (1))
sch 2 commenced 11 May 1989 (s 2 (2) and see Cwlth Gaz 1989 No S164)
Legislation after becoming Territory enactment
Scaffolding and Lifts Regulations Amendment SL 1999 No 19
notified 30 September 1999 (Gaz 1999 No S57)
commenced 30 September 1999 (s 1)
Occupational Health and Safety Legislation Regulations Amendment SL 2000 No 47 pt 3
notified 30 November 2000 (Gaz 2000 No 48)
commenced 30 November 2000 (s 1)
Statute Law Amendment Act 2001 No 11 sch 3
notified 29 March 2001 (Gaz 2001 No 13)
commenced 29 March 2001 (s 2)
Legislation (Consequential Amendments) Act 2001 No 44 pt 359
notified 26 July 2001 (Gaz 2001 No 30)
s 1, s 2 commenced 26 July 2001 (IA s 10B)
pt 359 commenced 12 September 2001 (s 2 and see Gaz 2001 No S65)
Statute Law Amendment Act 2007 A2007-3 sch 3 pt 3.92
notified LR 22 March 2007
s 1, s 2 taken to have commenced 1 July 2006 (LA s 75 (2))
sch 3 pt 3.92 commenced 12 April 2007 (s 2 (1))
Work Safety Legislation Amendment Act 2009 A2009-28 sch 2 pt 2.11
notified LR 9 September 2009
s 1, s 2 commenced 9 September 2009 (LA s 75 (1))
sch 2 pt 2.11 commenced 1 October 2009 (s 2 and see Work Safety Act 2008 A2008-51, s 2 (1) (b) and CN2009-11)
Name of
regulation
s 1 am regs gazetted 9
March 1956; regs gazetted 22 June
1956
om Act 1957 No 8 sch pt 2 (as
am ord 1977 No 28 s 5)
ins 1999 No
19 sch
am R2 LA
Dictionary
s
2 om Act 1957 No 8 sch pt 2 (as am ord 1977 No 28 s
4)
ins A2007-3 amdt
3.471
Notes
s
3 defs reloc to dict A2007-3 amdt
3.470
sub A2007-3 amdt
3.471
def chief inspector
ins Act 1957 No 8 sch pt
2
om A2007-3 amdt
3.469
def inspector
ins Act 1957 No 8 sch pt 2
om
A2007-3 amdt 3.469
def the
Act sub Act 1957 No 8 sch pt 2; Act 2001 No 11
amdt 3.257
om Act 2001 No 44
amdt 1.3879
def the Explosives
Act 1905 ins Act 1957 No 8 sch pt
2
om 1999 No 19 sch
s
8 sub regs gazetted 1 September
1950
om Act 1957 No 8 sch pt
2
s 9 om regs gazetted 1 September
1950
s 10 sub regs gazetted 1 September
1950
om Act 1957 No 8 sch pt
2
s 11 sub Act 1957 No 8 sch pt
2
s 12 om Act 1957 No 8 sch pt
2
pt 3 hdg om Act 1957 No 8 sch pt
2
s 15 om Act 1957 No 8 sch pt
2
Interpretation
div
4.1 hdg ins R2 LA
Design, construction and erection of
lifts
div 4.2 hdg (prev pt 4 div
A hdg) renum R2 LA
s 17 am Act 1957 No 8 sch pt 2; regs
renum R2 LA
s 18 ss renum R2 LA
s 22 ss renum R2 LA
s 23 ss renum R2 LA
s 24 ss renum R2 LA
s 25 sub regs gazetted 3 December
1954
ss renum R2 LA
s 27 ss renum R2 LA
s 28 ss renum R2 LA
s 29 ss renum R2 LA; ss renum R3
LA
s 31 ss renum R2 LA
s 32 ss renum R2 LA
s 33 ss renum R2 LA
s 35 am Act 1957 No 8 sch pt 2; Act
2001 No 11 amdt 3.258
s 39 ss renum R2 LA
s 40 ss renum R2 LA
s 41 ss renum R2 LA
s 46 ss renum R2 LA
s 51 ss renum R2 LA
s 56 ss renum R2 LA
s 61 ss renum R2 LA
s 62 ss renum R2 LA
s 63 ss renum R2 LA
Maintenance of
lifts
div 4.3 hdg (prev pt 4 div
B hdg) renum R2 LA
s 67 pars renum R2 LA
Use of
lifts
div 4.4 hdg (prev pt 4 div
C hdg) renum R2 LA
s 68 am 2000 No 47 s 11; ss etc renum
R2 LA
s 69 am Act 1957 No 8 sch pt
2
s 70 am 2000 No 47 s
12
s 72A ins regs gazetted 22 June
1956
sub Act 1957 No 8 sch pt 2 (as
am ord 1974 No 26 s 2; ord 1977 No 28
s 5)
am Act 1957 No 8 sch pt 2
(as am ord 1981 No 15 s 2; ord 1982 No 68 s
2)
om Act 1957 No 8 sch pt 2 (as am
ord 1983 No 34 s 5)
General
div
5.1 hdg (prev pt 5 div A hdg) renum R2 LA
s 73 am Act 1957 No 8 sch pt 2 (as am
ord 1976 No 7 s 2); ss etc renum R2 LA
s 75 ss renum R2 LA
s 76 om regs gazetted 22 June
1956
Construction, erecting, adding to, altering,
repairing, finishing, painting and cleaning buildings and
structures
div 5.2 hdg (prev pt 5
div B hdg) renum R2 LA
s 78 ss renum R2 LA
s 79 ss renum R2 LA
s 80 ss renum R2 LA
s 81 ss renum R2 LA
s 82 am Act 1957 No 8 sch pt 2; Act
2001 No 11 amdt 3.259; ss etc renum R2 LA
s 83 am Act 1957 No 8 sch pt 2; ss etc
renum R2 LA
Demolition of buildings and
structures
div 5.3 hdg (prev pt 5
div C hdg) renum R2 LA
s 84 am regs gazetted 22 June 1956;
1999 No 19 sch; ss etc renum R2 LA; A2009-28 amdt 2.27
s 86 ss etc renum R2
LA
s 87 am regs gazetted 3 December 1954;
ss etc renum R2 LA
s 88 ss renum R2 LA
s 89 ss etc renum R2
LA
s 90 ss renum R2 LA
s 91 ss etc renum R2
LA
s 92 ss etc renum R2
LA
s 93 ss etc renum R2
LA
s 94 ss renum R2 LA
General
div
7.1 hdg (prev pt 7 div A hdg) renum R2 LA
s 95 am regs gazetted 3 December 1954;
regs gazetted 22 June 1956; ss renum R2 LA
Cofferdams and
caissons
div 7.2 hdg (prev pt 7
div B hdg) renum R2 LA
Trenches
div
7.3 hdg (prev pt 7 div C hdg) renum R2 LA
s 97 ss renum R2 LA
Shafts, wells and
tunnels
div 7.4 hdg (prev pt 7
div D hdg) renum R2 LA
s 98 ss renum R2 LA
Diving
div
8.1 hdg (prev pt 8 div A hdg) renum R2 LA
s 99 am regs gazetted 22 June 1956;
Act 1957 No 8 sch pt 2; 1999 No 19 sch; ss etc renum R2 LA
Tunnelling
div
8.2 hdg (prev pt 8 div B hdg) renum R2 LA
s 100 am regs gazetted 22 June 1956;
Act 1957 No 8 sch pt 2; 1986 No 9 s 3; 1999 No 19 sch; ss etc renum
R2 LA
Caissons
div
8.3 hdg renum R2 LA
s 101 am regs gazetted 22 June 1956;
Act 1957 No 8 sch pt 2; 1986 No 9; 1999 No 19 s 2 sch; ss etc renum R2
LA
pt 9 hdg om 1999 No 19
sch
s 102 om 1999 No 19
sch
s 103 am Act 1957 No 8 sch pt
2
om 1999 No 19 sch
s 104 om 1999 No 19
sch
s 105 om 1999 No 19
sch
s 106 om 1999 No 19
sch
s 107 om 1999 No 19
sch
s 108 om 1999 No 19
sch
s 109 om 1999 No 19
sch
s 110 om 1999 No 19
sch
s 111 om 1999 No 19
sch
s 112 om 1999 No 19
sch
s 113 om 1999 No 19
sch
s 114 om 1999 No 19
sch
s 115 om 1999 No 19
sch
s 116 om 1999 No 19
sch
s 117 om 1999 No 19
sch
s 118 om 1999 No 19
sch
Explosive-powered tools—safety
measures
pt 9A hdg sub A2007-3
amdt 3.472
s 118A ins regs gazetted 9 March
1956
s 118B ins regs gazetted 9 March 1956;
ss etc renum R2 LA
s 118C ins regs gazetted 9 March 1956;
ss renum R2 LA
s 118D ins regs gazetted 9 March 1956;
ss etc renum R2 LA
s 118E ins regs gazetted 9 March 1956;
ss etc renum R2 LA
s 118F ins regs gazetted 9 March 1956;
ss renum R2 LA
s 118G ins regs gazetted 9 March 1956;
ss renum R2 LA
s 118H ins regs gazetted 9 March
1956
First-aid
equipment
div 10.1 hdg (prev pt
10 div A hdg) renum R2 LA
s 119 am regs gazetted 3 December
1954; ss renum R2 LA
Shelter, change and dining
accommodation
div 10.2 hdg (prev
pt 10 div B hdg) renum R2 LA
s 120 ss etc renum R2
LA
Sanitary conveniences and washing
facilities
div 10.3 hdg (prev pt
10 div C hdg) renum R2 LA
s 121 am Act 1957 No 8 sch pt 2 (as am
ord 1968 No 5 s 2); 1986 No 9 s 4; ss etc renum R2 LA
s 122 am Act 1957 No 8 sch pt 2; ss
etc renum R2 LA
s 123 ss renum R2 LA
s 124 ss renum R2 LA
s 125 ss renum R2 LA
s 126 ss etc renum R2
LA
s 127 am regs gazetted 5 August 1955;
Act 2001 No 11 amdt 3.260; ss etc renum R2 LA
s 128 ss renum R2 LA
s 129 ss renum R2 LA
s 130 am regs gazetted 3 December
1954; ss renum R2 LA
s 131 ss renum R2 LA
s 132 am regs gazetted 5 August 1955;
ss etc renum R2 LA
s 132A ins regs gazetted 1 March 1957;
ss renum R2 LA
s 133 ss renum R2 LA
s 134 ss renum R2 LA
s 135 ss renum R2 LA
s 136 ss renum R2 LA
s 137 ss renum R2 LA
s 138 am 2000 No 47 s 13; ss renum R2
LA
s 139 ss etc renum R2
LA
s 140 ss renum R2 LA
s 141 ss renum R2 LA
s 142 ss etc renum R2
LA
s 143 am Act 1957 No 8 sch pt 2; Act
2001 No 11 amdt 3.261; ss etc renum R2 LA
s 144 am regs gazetted 19 October
1956; Act 2001 No 11 amdt 3.262; ss etc renum R2 LA
s 145 ss etc renum R2
LA
s 150 pars renum R2
LA
s 151 ss renum R2 LA
s 154 pars etc renum R2
LA
s 156 ss etc renum R2
LA
s 157 ss renum R2 LA
s 158 ss etc renum R2
LA
pt 14 hdg om 2000 No 47 s
14
s 159 am regs gazetted 3 December
1954; Act 1957 No 8 sch pt 2 (as am ord 1976 No 7 s 3; ord 1977 No 28 s 5; ord
1983 No 34 s 5)
om 2000 No
47 s 14
s 160 am regs gazetted 3 December
1954; Act 1957 No 8 sch pt 2
om 2000
No 47 s 14
s 161 am regs gazetted 3 December
1954; Act 1957 No 8 sch pt 2
om 2000
No 47 s 14
pt 15 hdg om 2000 No 47 s
14
s 162 am regs gazetted 3 December
1954; Act 1957 No 8 sch pt 2 (as am ord 1977 No 28 s 5; ord 1983 No 34 s
5)
om 2000 No 47 s
14
s 163 om Act 1957 No 8 sch pt 2 (as am
ord 1983 No 34 s 5)
s 164 am Act 1957 No 8 sch pt 2 (as am
ord 1977 No 28 s 4); ss renum R2 LA
sch 1 am regs gazetted 3 November
1950; regs gazetted 6 March 1953; regs gazetted 22 June 1956; Act 1957 No 8 sch
pt 2 (as am ord 1976 No 7 s 2; ord 1977 No 28 s 5; ord 1982 No 15 s 2; ord
1982 No 68 s 2)
om Act 1957 No
8 sch pt 2 (as am ord 1983 No 34 s 5)
sch 2 am regs gazetted 22 June 1956;
regs gazetted 19 October 1956
om Act
1957 No 8 sch pt 2
Method of treatment of silica paint for the
purpose of ascertaining the percentage of free silica
present
sch 3 hdg (prev third sch
hdg) renum R2 LA
sch 3 items renum R2
LA
Processes to which regulation 73 (1) (o)
applies
sch 4 hdg (prev fourth
sch hdg) renum R2 LA
Method of treatment of a lead compound for
the purpose of determining the percentage of dry compound of
lead
sch 5 hdg (prev fifth sch
hdg) renum R2 LA
sch 5 items renum R2
LA
sch 6 om 1999 No 19
sch
sch 7 hdg (prev seventh sch hdg) renum
R2 LA
Medical standards and examination report for
compressed air workers
sch 8
hdg (prev eighth sch hdg) renum R2
LA
sch 8 pars renum R2
LA
Symptoms and treatment of compressed air
illness
sch 9 hdg (prev ninth sch
hdg) renum R2 LA
sch 9 cl etc renum
R2 LA
Dictionary
dict ins
A2007-3 amdt 3.473
def
analogous reloc from s 3 A2007-3 amdt
3.470
def approved
reloc from s 3 A2007-3 amdt
3.470
def axial stress
reloc from s 3 A2007-3 amdt
3.470
def bearing pressure
reloc from s 3 A2007-3 amdt
3.470
def birdcage scaffolding
ins A2007-3 amdt 3.473
def
cantilever scaffolding ins A2007-3 amdt
3.473
def conveyor ins
A2007-3 amdt 3.473
def dead
loads reloc from s 3 A2007-3 amdt
3.470
def designed
reloc from s 3 A2007-3 amdt
3.470
def drawings
reloc from s 3 A2007-3 amdt
3.470
def dynamically
irreversible reloc from s 3 A2007-3
amdt 3.470
def
dynamically reversible reloc from s 3 A2007-3
amdt 3.470
def
explosive-powered tool ins A2007-3 amdt
3.473
def fixed end
reloc from s 3 A2007-3
amdt 3.470
def forged
steel reloc from s 3 A2007-3
amdt 3.470
def free end
reloc from s 3 A2007-3
amdt 3.470
def heavy duty
scaffolding ins A2007-3 amdt
3.473
def high tensile
structural steelreloc from s 3 A2007-3
amdt 3.470
def hinged end
reloc from s 3 A2007-3
amdt 3.470
def in
commission reloc from s 3 A2007-3
amdt 3.470
def
independent pole scaffolding ins A2007-3 amdt
3.473
def light duty
scaffolding ins A2007-3 amdt
3.473
def light swinging stage
ins A2007-3 amdt 3.473
def
limiting reloc from s 3 A2007-3
amdt 3.470
def live loads
reloc from s 3 A2007-3
amdt 3.470
def mild steel
reloc from s 3 A2007-3
amdt 3.470
def projectile
ins A2007-3 amdt 3.473
def
qualified operator ins A2007-3 amdt
3.473
def roller reloc
from s 3 A2007-3 amdt 3.470
def
run ins A2007-3 amdt
3.473
def S.A.A. Wiring Rules
reloc from s 3 A2007-3
amdt 3.470
def safety
gear ins A2007-3 amdt
3.473
def safe working load
(or working load) reloc from s 3 A2007-3
amdt 3.470
def
second-hand reloc from s 3 A2007-3
amdt 3.470
def section
reloc from s 3 A2007-3
amdt 3.470
def service
lift ins A2007-3 amdt
3.473
def single pole
scaffolding ins A2007-3 amdt
3.473
def static
counterbalance weights reloc from s 3 A2007-3
amdt 3.470
def strength
reloc from s 3 A2007-3
amdt 3.470
def stress
reloc from s 3 A2007-3
amdt 3.470
def suspended
scaffolding ins A2007-3 amdt
3.473
def toe board
ins A2007-3 amdt 3.473
def
tool ins A2007-3 amdt
3.473
def transverse stress
reloc from s 3 A2007-3
amdt 3.470
def under
power reloc from s 3 A2007-3
amdt 3.470
def use
ins A2007-3 amdt 3.473
def
work ins A2007-3 amdt
3.473
def working load
reloc from s 3 A2007-3 amdt 3.470
Some earlier republications were not numbered. The number in column 1 refers to the publication order.
Since 12 September 2001 every authorised republication has been published in electronic pdf format on the ACT legislation register. A selection of authorised republications have also been published in printed format. These republications are marked with an asterisk (*) in column 1. Electronic and printed versions of an authorised republication are identical.
|
Republication No |
Amendments to |
Republication date |
|
1 |
SL 1986 No 9 |
31 October 1993 |
|
2 |
A2001-44 |
11 September 2002 |
|
3 |
A2001-44 |
4 November 2004 |
|
4 |
A2007-3 |
12 April 2007 |
© Australian Capital Territory 2009